Warning

You are reading an old version of this documentation. If you want up-to-date information, please have a look at 2024.6 .

Add-on instructions description

AO_Execute_Sequence

Inputs and Outputs description

This Add-On instruction can be used to trigger the execution of a vibration sequence. This Add-On instruction also allows to turn ON or OFF the backlight of the Asycube. One instance of this instruction is used per Asycube.

Fig. 186 AO_Execute_Sequence

Table 49 Inputs

Variable	Type	Description
boStartPIN	Boolean	A rising edge starts the sequence.
boStopPIN	Boolean	A rising edge stops the sequence.
		If the system is in Error state, a rising edge clears the error.
inSeqIDPIN	Integer	Vibration recipe ID (1..26)
inVibrationSetPIN	Integer	Vibration recipe ID (1..26)
inNbPartsPIN	Integer	Number of remaining parts currently on the Asycube.
inNbPartsMaxPIN	Integer	Desired number of parts that you want on the Asycube.
inXPosPIN	Integer	X Coordinate of the center of mass of the remaining parts (-100..100). Corresponds to 100x the values described in the coordinate system for the center of mass.
inYPosPIN	Integer	Y Coordinate of the center of mass of the remaining parts (-100..100). Corresponds to 100x the values described in the coordinate system for the center of mass.
boBacklightPIN	Boolean	Turns ON and OFF the backlight
boGatewayConnectionFaultPIN	Boolean	Connection fault status of the gateway.

Table 50 Outputs

Variable	Type	Description
inStatePOU	Integer	State : 0 = Idle, 1 = Running, 2 = Stopping, 10 = Error
boDonePOU	Boolean	A rising edge indicates the end of the sequence
boBacklightStatePOU	Boolean	State: TRUE = backlight ON, FALSE = Backlight OFF
diRemainingTimePOU	Double Integer	Remaining time of the sequence
boErrorPOU	Boolean	Goes to TRUE if an error occurred on the block
inErrorIDPOU	Integer	Error ID (See Error List)
stErrorNamePOU	String	Error Description (See Error List)

Table 51 Inputs/Outputs

Variable	Type	Description
regAsycubeWritePIO	Integer[0..33]	This input must be linked to the GVL structure containing the write registers (See Plugin installation and configuration to import the structure)
regAsycubeReadPIO	Integer[0..33]	This input must be linked to the GVL structure containing the read registers (See Plugin installation and configuration to import the structure)

Error List

Table 52 FB_Execute_Sequence - Error List

N°	ID	Cause	Resolution
700	Transition error	Input that was activated is not allowed in the current state.	Only use command when you are in the correct state.
701	Modbus error	Refer to Main Modbus exception codes
702	Internal Modbus error	Refer to Holding Register: error codes
703	Warning	Refer to Asycube warnings and alarms
704	Alarms	Refer to Asycube warnings and alarms
705	Gateway disconnected from PLC	Communication problem on the Ethernet/IP segment	Check the cable between gateway and PLC
706	Asycube disconnected from gateway	Communication problem on the Modbus TCP segment	Check the cable between gateway and Asycube
707	Time out	Connection was lost with the Asycube	Check the cables. Check that the Asycube is supplied. Check the Gateway state.
708	Wrong parameter	Wrong input parameter	Correct the wrong input parameter.
709	-	N/A	-

AO_Execute_Platform_Vibration

This Add-On instruction is used to execute a single platform vibration. Standard vibration or centering vibration can be triggered using this instruction.

Inputs and Outputs description

Fig. 187 AO_Execute_Platform_Vibration

Table 53 Inputs

Variable	Type	Description
inSelectModePIN	Integer	Mode: 0 = Standard vibration, 1 = Centering vibration
boStartPIN	Boolean	A rising edge starts the vibration.
boStopPIN	Boolean	A rising edge stops the vibration. If the system is in Error state, a rising edge clears the error.
inVibrationIDPIN	Integer	Vibration ID (1..26)
inVibrationSetPIN	Integer	Set of vibration (1..26)
inXPosPIN	Integer	X Coordinate of the center of mass of the remaining parts (-100..100). Corresponds to 100x the values described in the coordinate system for the center of mass. Only if Mode = 1.
inYPosPIN	Integer	Y Coordinate of the center of mass of the remaining parts (-100..100). Corresponds to 100x the values described in the coordinate system for the center of mass. Only if Mode = 1.
diDurationPIN	Double Integer	Duration of vibration (0 = unlimited). Only if Mode = 0.
boGatewayConnectionFaultPIN	Boolean	Connection fault status of the gateway

Table 54 Outputs

Variable	Type	Description
inStatePOU	Integer	State : 0 = Idle, 1 = Running, 2 = Stopping, 10 = Error
boDonePOU	Boolean	A rising edge indicates the end of the sequence
diRemainingTimePOU	Double Integer	Remaining time of the vibration.
boErrorPOU	Boolean	Goes to TRUE if an error occurred on the block
inErrorIDPOU	Integer	Error ID (See Error List)
stErrorNamePOU	String	Error Description (See Error List)

Table 55 Inputs/Outputs

Variable	Type	Description
regAsycubeWritePIO	Integer[0..33]	This input must be linked to the GVL structure containing the write registers (See Plugin installation and configuration to import the structure)
regAsycubeReadPIO	Integer[0..33]	This input must be linked to the GVL structure containing the read registers (See Plugin installation and configuration to import the structure)

Error List

Table 56 FB_Execute_Platform_Vibration - Error List.

N°	ID	Cause	Resolution
710	Transition error	Input that was activated is not allowed in the current state.	Only use command when you are in the correct state.
711	Modbus error	Refer to Main Modbus exception codes
712	Internal Modbus error	Refer to Holding Register: error codes
713	Warning	Refer to Asycube warnings and alarms
714	Alarms	Refer to Asycube warnings and alarms
715	Gateway disconnected from PLC	Communication problem on the Ethernet/IP segment	Check the cable between gateway and PLC
716	Asycube disconnected from gateway	Communication problem on the Modbus TCP segment	Check the cable between gateway and Asycube
717	Time out	Connection was lost with the Asycube	Check the cables. Check that the Asycube is supplied. Check the Gateway state.
718	Wrong parameter	Wrong input parameter	Correct the wrong input parameter.
719	-	N/A	-

AO_Execute_Hopper_Vibration

This function block is used to execute a single hopper vibration. Standard vibration or Quantity Adjusted vibration can be triggered using this block.

Inputs and Outputs description

Fig. 188 AO_Execute_Hopper_Vibration

Table 57 Inputs

Variable	Type	Description
inSelectModePIN	Integer	Mode: 0 = Standard vibration, 1 = Centering vibration
boStartPIN	Boolean	A rising edge starts the vibration.
boStopPIN	Boolean	A rising edge stops the vibration. If the system is in Error state, a rising edge clears the error.
inVibrationIDPIN	Integer	Vibration ID (1..26)
inVibrationSetPIN	Integer	Vibration Recipe ID (1..26)
inNbPartsPIN	Integer	Number of remaining parts currently on the Asycube. Only if Mode = 1
inNbPartsMaxPIN	Integer	Desired number of parts that you want on the Asycube. Only if Mode = 1.
diDurationPIN	Double Integer	Duration of vibration (0 = unlimited). Only if Mode = 0.
boGatewayConnectionFaultPIN	Boolean	Connection fault status of the gateway

Table 58 Outputs

Variable	Type	Description
inStatePOU	Integer	State: 0 = IDLE, 1 = Running, 2 = Stopping, 10 = Error
boDonePOU	Boolean	A rising edge indicates the end of the vibration.
diRemainingTimePOU	Double Integer	Remaining time of the vibration.
boErrorPOU	Boolean	Goes to TRUE if an error occurred on the block
inErrorIDPOU	Integer	Error ID (See Error List)
stErrorNamePOU	String	Error Description (See Error List)

Table 59 Inputs/Outputs

Variable	Type	Description
regAsycubeWritePIO	Integer[0..33]	This input must be linked to the GVL structure containing the write registers (See Plugin installation and configuration to import the structure)
regAsycubeReadPIO	Integer[0..33]	This input must be linked to the GVL structure containing the read registers (See Plugin installation and configuration to import the structure)

Error List

Table 60 AO_Execute_Platform_Vibration - Error List.

N°	ID	Cause	Resolution
720	Transition error	Input that was activated is not allowed in the current state.	Only use command when you are in the correct state.
721	Modbus error	Refer to Main Modbus exception codes
722	Internal Modbus error	Refer to Holding Register: error codes
723	Warning	Refer to Asycube warnings and alarms
724	Alarms	Refer to Asycube warnings and alarms
725	Gateway disconnected from PLC	Communication problem on the Ethernet/IP segment	Check the cable between gateway and PLC
726	Asycube disconnected from gateway	Communication problem on the Modbus TCP segment	Check the cable between gateway and Asycube
727	Time out	Connection was lost with the Asycube	Check the cables. Check that the Asycube is supplied. Check the Gateway state.
728	Wrong parameter	Wrong input parameter	Correct the wrong input parameter.
729	-	N/A	-

FB_Backlight

This Add-On instruction is used to control the backlight. Backlight can be controlled in continuous or in flash mode.

Inputs and Outputs description

Fig. 189 AO_Backlight

Table 61 Inputs

Variable	Type	Description
boLightONPIN	Boolean	A rising edge turns ON the backlight
boLightOFFPIN	Boolean	A rising edge turns OFF the backlight If the system is in Error state, a rising edge clears the error.
diDurationPIN	Double Integer	Duration of the backlight. If 0, backlight turns OFF only if boLightOFFPIN is activated.
boGatewayConnectionFaultPIN	Boolean	Connection fault status of the gateway.

Table 62 Outputs

Variable	Type	Description
inStatePOU	Word	State: 0 = IDLE, 1 = Running, 2 = Stopping, 10 = Error
tiRemainingTimePOU	Double Integer	Remaining time of backlight. If tiDurationPIN ≠ 0.
boErrorPOU	Boolean	Goes to TRUE if an error occurred on the block
inErrorIDPOU	Integer	Error ID (See Error List)
stErrorNamePOU	String	Error Description (See Error List)

Table 63 Inputs/Outputs

Variable	Type	Description
regAsycubeWritePIO	Integer[0..33]	This input must be linked to the GVL structure containing the write registers (See Plugin installation and configuration to import the structure)
regAsycubeReadPIO	Integer[0..33]	This input must be linked to the GVL structure containing the read registers (See Plugin installation and configuration to import the structure)

Error List

Table 64 AO_Backlight - Error List.

N°	ID	Cause	Resolution
730	Transition error	Input that was activated is not allowed in the current state.	Only use command when you are in the correct state.
731	Modbus error	Refer to Main Modbus exception codes
732	Internal Modbus error	Refer to Holding Register: error codes
733	Warning	Refer to Asycube warnings and alarms
734	Alarms	Refer to Asycube warnings and alarms
735	Gateway disconnected from PLC	Communication problem on the Ethernet/IP segment	Check the cable between gateway and PLC
736	Asycube disconnected from gateway	Communication problem on the Modbus TCP segment	Check the cable between gateway and Asycube
737	Time out	Connection was lost with the Asycube	Check the cables. Check that the Asycube is supplied. Check the Gateway state.
739	-	N/A	-