Avertissement

Vous lisez une ancienne version de cette documentation. Si vous souhaitez obtenir des informations actualisées, veuillez consulter 2024.12 .

Standard hoppers

The standard hoppers sold by Asyril include:

../../../_images/hoppers_240.png

Fig. 56 Standard hoppers for Asycube 240, 380 and 530, including control unit

(A) The container (see Interfaces mécaniques) receiving the parts. Depending on the size of the parts to be fed and the required machine autonomy, different sizes may be used (1L, 2L, 3L, 10L or 15L). These containers are in stainless steel Inox 1.4301.

(B) The linear vibrator (see Interfaces mécaniques) that moves the parts on the container to feed the Asycube.

(C) The Unité de contrôle used to adjust the hopper vibration amplitude.

A set of three different cables is also included (see Interfaces électriques).

Instructions de démarrage rapide

  1. Remove contents from box:

  • 1x hopper unit

  • 1x hopper control unit

  • 3x cables (mains power cable, actuator power cable, digital control cable)

  1. Install and mount the hopper, see more details in Montage.

  2. Install the hopper control unit, see more details in Montage.

  3. Connect the digital control cable from the Asycube digital output port to the hopper control unit.

  4. Connect the actuator power cable from the hopper to the hopper control unit.

  5. Connect to mains, either 115V or 230V and 50Hz or 60Hz.

Important

The input voltage and frequency must match the voltage and frequency of the hopper vibrating mechanism. If this is not respected, the hopper could be irreversibly damaged.

  1. Turn the hopper control unit ON/OFF switch to ON.

  2. Enable the digital output of the Asycube.

  3. Confirm that the hopper is vibrating.

  4. Adjust the vibration level as needed with the potentiometer (0-100%) on the hopper control unit.

Interfaces électriques

Schéma de câblage

The hopper is supplied with the controller and cables ready to be installed. The Tableau 8 gives the current ratings for the different type of hoppers.

Important

The input voltage and frequency must match the voltage and frequency of the hopper vibrating mechanism. If this is not respected, the hopper could be irreversibly damaged.

Tableau 8 Current ratings

Hopper type

AC characteristics

Actuator nominal current

Recommended rated current

Trémie 1L

115VAC/50 or 60Hz

0.17A

1A 1

230VAC/50 or 60Hz

0.08A

1A 1

2L/3L Hopper

115VAC/50 or 60Hz

1.32A

2A 1

230VAC/50 or 60Hz

0.6A

2A 1

10L/15L Hopper

115VAC/50 or 60Hz

1.32A

2A 1

230VAC/50 or 60Hz

0.6A

2A 1
1 all controllers have an integrated fuse of type 5x20mm, 6.3A, class T

The cables length supplied with the hopper and the wiring diagram are shown in Fig. 57. The signal polarity of the controller cable is detailed in Tableau 9.

../../../_images/cable_length.png

Fig. 57 Wiring diagram and cables length

Tableau 9 Signal polarity of Controller cable

Numéro

Signal

Fils internes

Câble de l’unité de contrôle de la trémie

1

L

Identifié par un 1 ou brun

Cab

2

N

Identifié par un 2 ou bleu

3

PE

Mise à terre (vert/jaune)

Unité de contrôle

../../../_images/control_unit.png

Fig. 58 Unité de contrôle

(A) Actuator power cable: connects the hopper controller to the linear vibrator.

(B) Digital control cable: connects the hopper controller to the Asycube.

(C) Mains power cable: connects the hopper controller to the mains supply.

The dimensions of the control unit including the supplied mounting bracket are detailed in Fig. 59.

../../../_images/control_unit_mecha.png

Fig. 59 Unité de contrôle

Remarque

Position the control unit so that you can reach the potentiometer.

Interfaces mécaniques

The different variants of hoppers (1L, 2L, 3L, 10L and 15L) can be mounted on the back or on the side of the Asycube. This enables applications such as multi-feeding where multiple different parts are being fed onto the same Asycube simultaneously via multiple hoppers, as illustrated in Fig. 60.

../../../_images/simple_vs_dual_feeding.png

Fig. 60 Illustration of single part feeding versus multi-feeding with two parts

Remarque

With multi-feeding applications, since both parts will share the same vibration settings, attention must be paid to how parts are combined. A very heavy and large part combined with a light and small one might not give satisfying results. Since many factors can affect the vibration characteristics, we strongly advise you to perform some preliminary tests first.

The table below summarizes which hopper size can be used in conjunction with which Asycube with single part feeding or multi-feeding applications:

Tableau 10 Single part feeding

Trémie 1L

Trémie 2L

Trémie 3L

Trémie 10L

Trémie 15L

Asycube 240

yes

yes

yes

N/A

N/A

Asycube 380

yes

yes

yes

yes

yes 1

Asycube 530

yes

yes

yes

yes

yes
Tableau 11 Multi-feeding with two parts

Trémie 1L

Trémie 2L

Trémie 3L

Trémie 10L

Trémie 15L

Asycube 240

yes

N/A

N/A

N/A

N/A

Asycube 380

yes

yes

yes

yes 2

N/A

Asycube 530

yes

yes

yes

yes 2

yes 2
1 single part feeding possible on the long side of the Asycube only.
2 multi-feeding with two parts possible on different short sides of the Asycube only.

Remarque

Les trémies 2L et 3L sont livrées avec des pieds de montage qui peuvent être fixés à la base de la machine directement à la bonne hauteur pour un Asycube 240 à l’aide de quatre vis M8x20.

Remarque

When pairing 1L, 2L, 3L, 10L and 15L hoppers with Asycube 380 and Asycube 530, the optional modular hopper fixing kit allows the hopper to be mounted at the ideal height.

Remarque

When two hoppers can be mounted on the same long side of the Asycube, a multi-feeding application with up to 4 parts can also be considered by mounting 4 hoppers symmetrically. If your application requires a configuration with more than two hoppers, please visit the multi-feeding section in EYE+ documentation or contact our support team from our website.

The following diagrams represent at which height the different hoppers shall be mounted and the position of the holes to fix the hopper to the machine base plate for single part feeding and multi-feeding with two parts.

Trémie de 1 L

../../../_images/1l_hopper_interfaces.png

Fig. 61 Single part feeding: Asycube 240 with 1 L hopper

Trémie de 2 L

../../../_images/2l_hopper_interfaces.png

Fig. 67 Single part feeding: Asycube 240 with 2 L hopper

Interfaces mécaniques Trémie de 3 L

../../../_images/3l_hopper_interfaces.png

Fig. 72 Single part feeding: Asycube 240 with 3 L hopper

Interfaces mécaniques Trémie de 10 L

../../../_images/10l_hopper_interfaces_380.png

Fig. 77 Single part feeding: Asycube 380 with 10 L hopper and fixing kit

../../../_images/10l_hopper_interfaces_without_380.png

Fig. 78 Single part feeding: Asycube 380 with 10 L hopper (no fixing kit)

Interfaces mécaniques Trémie de 15 L

../../../_images/15l_hopper_interfaces.png

Fig. 81 Single part feeding: Asycube 530 with 15 L hopper with fixing kit

../../../_images/15l_hopper_interfaces_without.png

Fig. 82 Single part feeding: Asycube 530 with 15 L hopper (no fixing kit)

Kit de fixation modulaire

Conseil

Cette section ne concerne que les Asycubes 380/530.

Le kit de fixation modulaire permet de positionner la trémie à une hauteur parfaitement adaptée à aux Asycubes 380/530. Les instructions de montage sont expliquées ci-dessous :

Étape 1

Choisissez la hauteur de fixation et fixez la première moitié avec 2 vis M5.

../../../_images/modular_fix_kit_step1.png

Remarque

La hauteur du kit de fixation peut être réglée de 180 à 255 mm par pas de 15 mm.

Étape 2

Sécurisez en fixant les 4 vis M8 avec écrous.

../../../_images/modular_fix_kit_step2.png

Étape 3

Répétez les étapes 1 et 2 pour la seconde moitié.

../../../_images/modular_fix_kit_step3.png

Étape 4

Fixez le kit de fixation modulaire sur la plateforme de base de la machine, puis fixez la trémie sur le kit de fixation.

../../../_images/modular_fix_kit_step4.png