警告

これは、古いバージョンのドキュメントです。 最新の情報をご覧になりたい場合は、次をご覧ください。 2024.12 .

Plugin installation and configuration

The plugin is delivered in a .zip folder. Unzip it and you will find the library.

• Library_PluginMitsubishiCCLinkAsycube(iQ-R).usl

• Library_PluginMitsubishiCCLinkAsycube(iQ-F).usl

• SYCON project to modify the transmission speed (Baud rate) of the Gateway see Change the transmission speed (Baud rate) of the gateway (Optional) (in the folder Gateway Configuration)

図 127 Content of the library

Installation of the library

1. Click on Project > Library Operation > Register to library List > User Library..

図 128 Import a Library

2. Add the Library_PluginMitsubishiCCLinkAsycube.usl.

Add the register file

1. Add the holding registers to Structured Data Types of your project.

図 129 Add Structured Data Types

2. Add the dbGateway to Global Label of your project. Should you have several Asycube, you can simply duplicate this label or its content. If GX Works 3 asks you to overwrite the registry files, because they are already present, select Yes.

図 130 Add Global Label

Add the Gateways in the configuration

1. Configure your CC-Link module > Required Settings according to below parameters. The default transmission speed of the Asycube Gateway is 10Mbps. Should you want to change it please refer to Change the transmission speed (Baud rate) of the gateway (Optional).

図 131 Required Settings

2. On your CC-Link module > Basic Settings, click on Network Configuration Setting.

図 132 Basic Settings

1. Set the Mode Setting to Ver. 2 Mode and verify the TX Speed. Click on Detect Now.

図 133 CC-Link Configuration I/O

2. You should now see all the remote station (one per Gateway/Asycube).

3. Check that the parameters are as in 図 133.

4. Click on Close with Reflecting the Setting.

3. On your CC-Link module > Basic Settings, click to Link Refresh Settings.

図 134 Basic Settings

1. Create a link between the CC-Link module and the CPU as shown in 図 134 (for one Gateway/Asycube which station address is 1) and press Apply :

図 135 Link between CC-Link module and CPU

Link I/O

Once the gateway has been successfully integrated into your project, you must assign the registers (data) of the Gateway in the Global Label.

1. Select the dbGateway Label.

2. Click on Detailed Setting of regAsycubeRead.

図 136 Global labels of library

1. When you assign the first address of the device, the following address are automatically completed.

図 137 Address of regAsycubeRead

3. Perform the same operation for regAsycubeWrite.

図 138 Address of refAsycubeWrite

Connect the registers to the FB

You must use the register variables instantiated in the global variables (regAsycubeWrite and regAsycubeRead) at the input of the different blocks. The variable boConnectionFaultedSB must also be set using the station status variable of your device (1 = remote device disconnected, 0 = normally situation).

Here is an example of an application with the input and output registers filled in.

図 139 Example of integration

Change the transmission speed (Baud rate) of the gateway (Optional)

The default Baud rate may not be suitable for all application. If you need to modify the Baud rate, please follow this procedure:

1. Download the Hilscher SYCON.net software tool.

2. Install the Hilscher SYCON.net software tool.

3. Launch the Hilscher SYCON.net software tool: click OK without Password.

4. Open the cclink project provided with the plugin.

1. Click Open

図 140 Open a project

2. Browse for the cclink.spj file delivered with the plugin.

図 141 Open cclink.spj

3. Click “Open”

5. Modify the Baud rate.

1. Right-click on the netTAP item.

2. Select Configuration - CC-Link Slave.

図 142 Select Configuration -> CC-Link Slave

3. Set the Baud rate to the desired value.

図 143 Set the Baud rate to the desired value

4. Click OK.

6. Connect your Asycube CC-Link Gateway to your computer.

1. Connect the 24VDC power supply (電源接続)

2. Connect the provided USB cable to your Gateway (under the flap).

3. Connect the provided USB cable to your computer.

7. Download the configuration into your Gateway.

1. Right-click on the netTAP item.

2. Click Download.

図 144 Download the configuration into the Gateway

3. If you get a warning Do you really want to download?, click Yes.

4. Wait a few seconds until the download succeed.

8. Finalize.

1. Exit SYCON.net software tool.

2. Remove the USB cable.

3. Disconnect the power supply.